The bronzing machine is a very important equipment in the post-press processing of the packaging printing industry. When the shopping bag needs to be bronzing, the special design of the bronzing machine with the cantilever structure will make the bronzing perfect. The cantilever structure of the bronzing machine can conveniently put the shopping bag on the cantilever workbench. At the same time, the bronzing machine adopts a hydraulic system, which can realize concave and convex embossing and three-dimensional bronzing for the shopping bags of high-grade brand goods.
When you are shopping in a shopping mall, merchants often put the goods in their shopping bags and sell them together. The shopping bag is a free gift, in addition to the goods, so that you can carry it, the merchant will always use it to promote their brand. It is very common to print text or LOGO on top of shopping bags.
Brands that sell a lot of money may need offset printing, but a large number of small and medium-sized brands may prefer silkscreen and hot stamping. Silk screen printing and hot stamping are very suitable for decoration on the formed shopping bag. Although it is slow, it is adaptable and easy to change, so it is widely welcomed.
Packaging industry, Die cutting, Embossing, high precision stamping, Decorative painting wood products branded paste painting process requires a lot of pressure. Usually the pressure of the pneumatic hot stamping machine is difficult to more than 15 tons, more than 15 tons stamping pressure hydraulic drive could be considered.
Pneumatic bronzing machine to pass the gas pressure as a medium, there are a lot of uncertainty, because there is more room for the gas molecules, can easily be compressed, so the pressure delivered to the product surface, there would be a process of change. The distance between the liquid molecules is much smaller than gas molecules, once the pressure delivered to the product surface, the pressure will remain for a long time stability.
Hydraulic drive, the machine itself to be equipped with a complete hydraulic system, compared to the pneumatic hot stamping machine, the structure is more complex, some of which will be expensive.
For up to 800mm carbon fiber shaft, the heat transfer more difficult, but we have overcome many difficulties, and finally completed a set of automatic transfer machine.
1) carbon fiber material: Carbon fiber is made from organic fibers by carbonization and graphitization treatment obtained microcrystalline graphite materials. Similar to the microstructure of carbon fiber artificial graphite is turbostratic graphite structure. A mechanical performance of new materials, steel accounted for less than 1 / 4, the tensile strength of carbon fiber resin composite materials are generally in 3500Mpa above, is 7-9 times that of steel, tensile elastic modulus of 230 ~ 430Gpa also high in steel. Therefore, the specific strength of CFRP material intensity and the ratio of the density can be achieved 2000Mpa / (g/cm3) above, the specific strength of A3 steel only 59Mpa / (g/cm3) about a specific modulus than steel. Higher than the strength of the material, the smaller the component weight, higher than the modulus, the greater is the stiffness, in this sense indicates that the carbon fiber has broad application prospects in engineering. Carbon fiber is a carbon content higher than 90% of the inorganic polymer fibers. In which the carbon content higher than 99% of said graphite fibers. Carbon fiber axial strength and high modulus, non-creep, fatigue resistance, good heat and electrical conductivity between the metallic and metal between the thermal expansion coefficient, good corrosion resistance, low density of fibers, X-ray transparent too good. But its poor impact resistance, easy to damage, under the action of the acid oxidation, and metal composite occurs when the metal carbide, cementite and electrochemical corrosion. Therefore, before use of carbon fiber surface treatment. Carbon fiber shaft with the use of its excellent fatigue resistance. Through the experiment, as long as the transfer film adhesive layer to make the necessary improvements, the transfer of carbon fiber can achieve good results.
2) transportation; trough the use of the usual storage device can be placed about 150 shaft. As the inherent speed of thermal transfer, automatic transfer machine speed can reach 1200 per hour, higher speed depends on the overall structure of the machine, but given the long shaft, high speed could mean the loss of stability .
3) fixtures; double-stick-type structure, which is slender cylinder for the structure of commonly used products.
Servo shuttle workbench, Shuttle stroke:250mm;
Big inkwell size: 200*300mm pad plates;
Independent cylinder driven for rubber pad;
PLC operation system
Under normal circumstances, a bronzing machine will only install a set of hot stamping foil feeding device and winding device, only hot stamping one color bronzing film, if you want to hot stamp another color bronzing film, you must use another set hot stamping machine, some users may find the cost too high. To this end, we have developed a two-color hot stamping machine (H2-TC4060LPT), which adds a feeding and winding device to the original hot stamping machine, which can stamp two colors of bronzing film at one time. However, this bronzing machine can only be used if the two hot stamping patterns are far apart and parallel to each other.
Large size for 500*800mm paper;
Super pressure, suitable for large area bronzing, die cutting and indentation, paste;
Double-volume receiving device, suitable for two-color hot stamping;
Upgraded operation panel for easier operation;
High strength steel plate for excellent stability.